Mods I

President Walker II Test Mode

Frequency Chart:

Yaesu FT-991/A & FTDX-1200 / 3000 / 5000 60m Modification

Alan 48 XL Multi Extended Bands

Midland M10 High Power & Frequency Unlock

Albrecht AE-5890EU New Version 2018

Yaesu FTDX-101D

Remove the top cover and the cover below it and look for the heatsink. Next to it is a MATRIX. Look for TX-OUT J2002-2″. KS5 is the second upper right solder point. Add solder point and full reset. EU Version

Kenwood TS-890s

tti – 1100 Modifications:

Move resistor from R43 to R42

This allows access to:

25615-30105 AM/FM known as band rU

25610-30110 AM/FM known as band PX

All A (Alpha Channels between 25645mhz to top end of 29mhz

Midland CT-200 Expansion:

Stabo XH9006e High Power / 120 Channels:

President JFK II A+ (Modification CB Radio NL) Matthijs

K-PO HR2800 Available Bands:

Midland M-10 Export Mode & High Power: http://tinyurl.com/y74jv6rh

Albrecht AE:6690 Channel & Power Modification: http://tinyurl.com/zcyjbdh

Anytone Apollo II Programming Software: http://tinyurl.com/zdu5ev8

Anytone AT-5555 v6

Midland / Alan 42 Multi:

President Johnny III & Harry III Service Manual: http://tinyurl.com/kgq556y

CRT Millenium Export Mode:

CRT Millenium Instruction Manual: http://tinyurl.com/hyyd6ct

Anytone Apollo 1 Manual: http://tinyurl.com/hpq8lly

Anytone AT-300M (crt-8040) Russian Language Export Mode:

Anytone Apollo II Manual: http://tinyurl.com/hky9rgt

Anytone AT-778v Set Up Software V1.01 : http://tinyurl.com/jl9cos6

Anytone AT-6666 (QX-6666) Software V2.01 (Anytone Branded Radio) http://tinyurl.com/h829gx3

Anytone AT-778 UHF / VHF Software: http://tinyurl.com/zlhjwsg

Programming Cable Schematic

Anytone AT-300 / 310m Schematic: http://tinyurl.com/zwajsa2

Anytone Apollo II Software. V1.01 :http://tinyurl.com/zdu5ev8

Super Galaxy Extended 10m Coverage

Intek M-495 Power & M-795 Power Modification

TTI TCB-1100 (Move resistor from one place to other) 25.610-30.110 / 25.615-30.105

Team TS-6m (26.515-27.855 AM / FM) Cut the wire and move the jumper

Intek M-120 Enable rU & Po

Thunderpole T1000 Enable rU & Po (Break the solder contact)

Intek M-150 Enable rU & Po (Join the solder point)

Lafayette Zeus (25.615-28.305) Turn on with ASC and FC Pressed (add the wire)

Intek M-799 Plus (25.615-30.105 / 25.610-30.110) Remove LK6

Intek M-130 Plus (25.615-30.105 / 26.510-30.110) Remove LK2

CRT-7900 Freq Expand

Yaesu FT-991 MARS/CAP Remove all screws, remove display and front panel, remove metal plate on back of front panel and solder JP3003 and reset

Lincoln II + : http://tinyurl.com/hrrk7gl

You will see some make big song and dance about the above. Why? I’ve no ideas..

Intek HR-2800 Schematic: http://tinyurl.com/hmy9cak

Intek HR-2800: rU Bands & Others: http://tinyurl.com/jmnqz69

CRT-2000

Intek M-799 Plus rU Mode Expansion:

Alinco SR8T/E Unlock Bottom cover off and solder A & B solder points

Emperor Ninja rU Mode: http://tinyurl.com/grkpah8

Albrecht AE-7500 Ham Mode: http://tinyurl.com/j2ylqly

Albrecht AE-6790 / 6891 Power & Channel Modifications: http://tinyurl.com/zj5b4w2

Albrecht AE-6690 Power & Country Options: http://tinyurl.com/zcyjbdh

Albrecht AE-6190 Country Options: http://tinyurl.com/h5mnk4x

President Lincoln II 400 Channel Mode: http://tinyurl.com/jqtdkgx

President Johnny II ASC Service Manual: http://tinyurl.com/zv6bjfn

Albrecht AE-6110 Manual All Languages: http://tinyurl.com/he48eyh

President Lincoln II + Software (Works Only On + V1.01) http://tinyurl.com/jefzdsx

CRT Superstar 3900n and CRT Superstar 3900 EL: http://tinyurl.com/zr6qqoc

Superstar 3900 Red / Jopix 3900: http://tinyurl.com/h7z5dd2

Cobra 29 LX-EU

Team MC-8 Multi Circuit Diagram: http://tinyurl.com/h354oly

Midland M-10 Possible 10w Power Mod: Cut K501 (not tested as no radio)

CRT 8040: Top Right hand side, cut the white wire and move the jumper

Ranger RCI-2950DX ERF2030 Conversion: http://tinyurl.com/h3esdfp

Midland G9 PMR Power Modification: http://tinyurl.com/hoale9k

Anytone AT-5555N 2014 Production: http://tinyurl.com/hgby23y

Maycom EM-27 Expansion rU Mode: http://tinyurl.com/z5xuag4

Alan 48 Plus Multi B (rU & Trimmers) http://tinyurl.com/gprrw7d

Alan 78 Multi B (rU & Trimmers) http://tinyurl.com/hcgd5g4

M-Tech Legend III rU Mode 120 channels: http://tinyurl.com/haw4zq8

M-Tech Legend II rU Mode 120 Channels: http://tinyurl.com/z7gvgm5

M-Tech Legend 1 rU Mode 120 Channels: http://tinyurl.com/gmb7un6

Stryker SR-955HPC Programming Software: http://tinyurl.com/jx3xnnf

Superstar 3900 Export Modification (Which version it works on unknown)

SS3900_All_Istr

Jopix 2000 Export Modification:

JPX2000_All_Istr

Midland 8001 XT Modifications:

midland_8001xt_mods

Albrecht AE-7500 Amateur Mode:

AE7500 amateur mode

CRT Megapro Modification V2: http://tinyurl.com/gme6hae

CRT Megapro Software V3.01: http://tinyurl.com/h6wwpjw

CRT Superstar 6900 (N) Unlock:

CRT Superstar 9900 Version 1 Software (2014) http://tinyurl.com/jjc4oe7

CRT Superstar 9900 Version II Software (2015) http://tinyurl.com/hqhu2y6

CRT Superstar 7900 Version 1 Software: http://tinyurl.com/h4w4ksq

Danita 3000 Multi “Export Mode”

tti TCB-771 2w AM to 4w AM Power

tti 560 8 Watts Power:

Cobra 29LX EU Service Manual: http://tinyurl.com/hnqq5hh

CRT Megapro Software: http://tinyurl.com/h6wwpjw

tti 550 Bridge R50 For All The Goodies

tti 881 (Swap Resistor from filled place to empty space)

Tti TCB-880 Swap the resistor position

Midland M Zero Plus Export Modification:

Dynascan PMR Unlock channels & 2w Power: http://tinyurl.com/zxlrcfw

CRT Megapro Export Mode:

Cut the White wire and move the jumper, bands a-j and VFO Mode enabled

Icom IC-7300 Mars / CAP

Magnum1 Modifications:

http://tinyurl.com/j92cdn7

CRT 4CF Enable Full Transmit:

Modificatie CRT 4CF

Albrecht AE-6110 Adjustments (From Stefann) Should also be the same for the Anytone Smart CB

untitled

RM KL-7405 & KL 7505 Outside of 11m Transmit

KL7X05_F_Panel

Close the jumper and away you go

President Lincoln II V3 Echo Modification.

Some people complain about the large amount of echo even at the smallest settings in the menu. IF you are good at soldering then look at R630 and this is a 2k ohm resistor, swap it out with a 195k ohm resistor and the echo behaves much much better. Remember, invalidates warranty, small part, skill needed. Not for the faint of heart.

Albrecht AE-6110 & Anytone Smart (17-25w FM Power) Just FM not working in AM mode

9166_6

Solder two legs together, in effect shorting it out. I have looked at photos from Klaus “HF-Doktor” and from http://www.srcb.ro online and this appears the only point which is the same. Limits life of your radio, invalidates warranty’s and is generally not a Smart way. But this is the power modification Photo: http://www.neuner.de (c)

Anytone AT-5555N & CRT Superstar 7900

277900_9714_7

Solder closed OP1

CRT 7900 Software:http://www.filedropper.com/ss7900setup10011 (limited time only, when expires its gone)
Albrecht AE-2990 AFS

AE2990AFS-Amateur-extension-to-Multi-Mode-Features

Stabo XM-4060e

30042_8891_8

Wire and Jumper

Team TS-6M LCD

Cut the wire and move the jumper. 26515-27855 AM/FM unlocked. Bands a, b, c

3173_2556_3

Danita 310m

SAM_0002

Cut the wire and move the jumper. 25.1-30.1 AM/FM

Albrecht AE-4200 EU

AE4200EU Channel Options

AE4200EU, hi-low power

Team MobileCom. Export Mode

320400_9089_5

Close OP1 and OP2 with solder, and for 0 ending and high power use the same modification as CRT One

CRT:

CRT MIKE EXPAND Norm

CRT ONE Expand mode EN-FR

CRT MIKE-HL Power

President:

Lincoln II (Only for initial pieces of first edition 1000 pieces to update to v2) Not for new models

Grant II Schematic:

Grant II

Top Gun Quad 5 Export Mode and PCB Adjustments

Modification_Top_Gun_Quad-5_ENG

PCB Adjutments

President Lincoln II Export Mode

Lincoln II Export

Yaesu FT-991 MARS / CAP

FT-991-MARS-Mod

Midland Base Camp 446

Midland Base Camp 446[1]

Grant II Premium: (HF-Doktor Information)

218 thoughts on “Mods I

  1. Hi simon,
    I got an Intek KT-950EE. And (as you probably already know) it isn’t the export version ( KT-950XE ) and because of that the vhf only works from 144.000. – 146.000. Instead. 136.000 – 174.000 .
    I can’t find the mod anywhere and I hope you can help me.

    Thnx in advance
    Martin

    Like

    • Hi Martin. It’s software and cable unlock if older version and newer by key routine. We don’t have this unlock 😞 but we can ask around after the holiday weekend ends here
      Regards
      🧙‍♂️

      Like

    • Thnx for the reply.
      Unfortunately i don’t have the cable , so i hope this version can be modified by keys.
      If you could ask around that would be great.
      Thnx in advance ( again 🙂 )
      Martin

      Like

  2. Salve Simon sono in possesso di un Cobra 29 LX EU sto cercando qualche modifica per espandere le frequenze tu sai qualche cosa a riguardo ciò ti sarei grato .Vincenzo

    Like

  3. Hi, I wanted to know if you can in the crt ss 6900n v6 have the modification to do the 60 channels without losing the data when you do the reset? Thanks, Enrico

    Like

  4. Hello Simon looking for information on an Anytone AT-6666 for external S meter connection points, bhi DSP connection points, and connection points for an external VFO and schematics and also the service manual

    Secondly looking for connection points for the bhi DSP module external S-meter connection points in an Alinco DX-SR8T

    Like

  5. Hi Simon !
    First off thanks for the information on the power mods for the President Walker 2 CB. It is much appreciated. Do you have any mods you can share for increasing the modulation ? Again thanks for your work and advice !!! Mike

    Like

    • Hi Mike. There is a way to increase it, it’s on the blog. Sadly I’ll not announce it as each radios values are different and too many armchair engineers have messed up radios by not having test gear, not writing down values before modifying the equipment.. Then when they’ve a paperweight they cry!
      Regards
      Simon

      Like

    • Hi Simon,

      I completely understand your concerns about posting the mods for increasing modulation for the President Walker. I will not be doing this mod myself. I have an an experienced shop doing it for me. He told me if I could research the mod he would do it for me. He does not have the time to do the research, I looked and looked but I could not find it. I found the service manual and a link to a Polish company that sells the radio with the mods. Would you please consider emailing me the mod ? I promise, he is a great radio tech and has all the correct equipment. If something went wrong I certainly would not hold you responsible in any way. If you don’t feel comfortable, then that is OK too. No hard feelings !!

      Mike

      Like

  6. Hello, Simon
    Is there a way to add an external s-meter to a CRT SS6900 (at-5555 and so on..). WHERE can I take the signal?
    Thanks a lot.
    Patrice

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.