Alan 48 XL Multi Extended Bands
Midland M10 High Power & Frequency Unlock
Albrecht AE-5890EU New Version 2018
Yaesu FTDX-101D
Remove the top cover and the cover below it and look for the heatsink. Next to it is a MATRIX. Look for TX-OUT J2002-2″. KS5 is the second upper right solder point. Add solder point and full reset. EU Version
Kenwood TS-890s
tti – 1100 Modifications:
Move resistor from R43 to R42
This allows access to:
25615-30105 AM/FM known as band rU
25610-30110 AM/FM known as band PX
All A (Alpha Channels between 25645mhz to top end of 29mhz
Midland CT-200 Expansion:
Stabo XH9006e High Power / 120 Channels:
President JFK II A+ (Modification CB Radio NL) Matthijs
K-PO HR2800 Available Bands:
Midland M-10 Export Mode & High Power: http://tinyurl.com/y74jv6rh
Albrecht AE:6690 Channel & Power Modification: http://tinyurl.com/zcyjbdh
Anytone Apollo II Programming Software: http://tinyurl.com/zdu5ev8
Anytone AT-5555 v6
Midland / Alan 42 Multi:
President Johnny III & Harry III Service Manual: http://tinyurl.com/kgq556y
CRT Millenium Export Mode:
CRT Millenium Instruction Manual: http://tinyurl.com/hyyd6ct
Anytone Apollo 1 Manual: http://tinyurl.com/hpq8lly
Anytone AT-300M (crt-8040) Russian Language Export Mode:
Anytone Apollo II Manual: http://tinyurl.com/hky9rgt
Anytone AT-778v Set Up Software V1.01 : http://tinyurl.com/jl9cos6
Anytone AT-6666 (QX-6666) Software V2.01 (Anytone Branded Radio) http://tinyurl.com/h829gx3
Anytone AT-778 UHF / VHF Software: http://tinyurl.com/zlhjwsg
Programming Cable Schematic
Anytone AT-300 / 310m Schematic: http://tinyurl.com/zwajsa2
Anytone Apollo II Software. V1.01 :http://tinyurl.com/zdu5ev8
Super Galaxy Extended 10m Coverage
Intek M-495 Power & M-795 Power Modification
TTI TCB-1100 (Move resistor from one place to other) 25.610-30.110 / 25.615-30.105
Team TS-6m (26.515-27.855 AM / FM) Cut the wire and move the jumper
Intek M-120 Enable rU & Po
Thunderpole T1000 Enable rU & Po (Break the solder contact)
Intek M-150 Enable rU & Po (Join the solder point)
Lafayette Zeus (25.615-28.305) Turn on with ASC and FC Pressed (add the wire)
Intek M-799 Plus (25.615-30.105 / 25.610-30.110) Remove LK6
Intek M-130 Plus (25.615-30.105 / 26.510-30.110) Remove LK2
CRT-7900 Freq Expand
Yaesu FT-991 MARS/CAP Remove all screws, remove display and front panel, remove metal plate on back of front panel and solder JP3003 and reset
Lincoln II + : http://tinyurl.com/hrrk7gl
You will see some make big song and dance about the above. Why? I’ve no ideas..
Intek HR-2800 Schematic: http://tinyurl.com/hmy9cak
Intek HR-2800: rU Bands & Others: http://tinyurl.com/jmnqz69
CRT-2000
Intek M-799 Plus rU Mode Expansion:
Alinco SR8T/E Unlock Bottom cover off and solder A & B solder points
Emperor Ninja rU Mode: http://tinyurl.com/grkpah8
Albrecht AE-7500 Ham Mode: http://tinyurl.com/j2ylqly
Albrecht AE-6790 / 6891 Power & Channel Modifications: http://tinyurl.com/zj5b4w2
Albrecht AE-6690 Power & Country Options: http://tinyurl.com/zcyjbdh
Albrecht AE-6190 Country Options: http://tinyurl.com/h5mnk4x
President Lincoln II 400 Channel Mode: http://tinyurl.com/jqtdkgx
President Johnny II ASC Service Manual: http://tinyurl.com/zv6bjfn
Albrecht AE-6110 Manual All Languages: http://tinyurl.com/he48eyh
President Lincoln II + Software (Works Only On + V1.01) http://tinyurl.com/jefzdsx
CRT Superstar 3900n and CRT Superstar 3900 EL: http://tinyurl.com/zr6qqoc
Superstar 3900 Red / Jopix 3900: http://tinyurl.com/h7z5dd2
Cobra 29 LX-EU
Team MC-8 Multi Circuit Diagram: http://tinyurl.com/h354oly
Midland M-10 Possible 10w Power Mod: Cut K501 (not tested as no radio)
CRT 8040: Top Right hand side, cut the white wire and move the jumper
Ranger RCI-2950DX ERF2030 Conversion: http://tinyurl.com/h3esdfp
Midland G9 PMR Power Modification: http://tinyurl.com/hoale9k
Anytone AT-5555N 2014 Production: http://tinyurl.com/hgby23y
Maycom EM-27 Expansion rU Mode: http://tinyurl.com/z5xuag4
Alan 48 Plus Multi B (rU & Trimmers) http://tinyurl.com/gprrw7d
Alan 78 Multi B (rU & Trimmers) http://tinyurl.com/hcgd5g4
M-Tech Legend III rU Mode 120 channels: http://tinyurl.com/haw4zq8
M-Tech Legend II rU Mode 120 Channels: http://tinyurl.com/z7gvgm5
M-Tech Legend 1 rU Mode 120 Channels: http://tinyurl.com/gmb7un6
Stryker SR-955HPC Programming Software: http://tinyurl.com/jx3xnnf
Superstar 3900 Export Modification (Which version it works on unknown)
Jopix 2000 Export Modification:
Midland 8001 XT Modifications:
Albrecht AE-7500 Amateur Mode:
CRT Megapro Modification V2: http://tinyurl.com/gme6hae
CRT Megapro Software V3.01: http://tinyurl.com/h6wwpjw
CRT Superstar 6900 (N) Unlock:
CRT Superstar 9900 Version 1 Software (2014) http://tinyurl.com/jjc4oe7
CRT Superstar 9900 Version II Software (2015) http://tinyurl.com/hqhu2y6
CRT Superstar 7900 Version 1 Software: http://tinyurl.com/h4w4ksq
Danita 3000 Multi “Export Mode”
tti TCB-771 2w AM to 4w AM Power
tti 560 8 Watts Power:
Cobra 29LX EU Service Manual: http://tinyurl.com/hnqq5hh
CRT Megapro Software: http://tinyurl.com/h6wwpjw
tti 550 Bridge R50 For All The Goodies
tti 881 (Swap Resistor from filled place to empty space)
Tti TCB-880 Swap the resistor position
Midland M Zero Plus Export Modification:
Dynascan PMR Unlock channels & 2w Power: http://tinyurl.com/zxlrcfw
CRT Megapro Export Mode:
Cut the White wire and move the jumper, bands a-j and VFO Mode enabled
Icom IC-7300 Mars / CAP
Magnum1 Modifications:
CRT 4CF Enable Full Transmit:
Albrecht AE-6110 Adjustments (From Stefann) Should also be the same for the Anytone Smart CB
RM KL-7405 & KL 7505 Outside of 11m Transmit
Close the jumper and away you go
President Lincoln II V3 Echo Modification.
Some people complain about the large amount of echo even at the smallest settings in the menu. IF you are good at soldering then look at R630 and this is a 2k ohm resistor, swap it out with a 195k ohm resistor and the echo behaves much much better. Remember, invalidates warranty, small part, skill needed. Not for the faint of heart.
Albrecht AE-6110 & Anytone Smart (17-25w FM Power) Just FM not working in AM mode
Solder two legs together, in effect shorting it out. I have looked at photos from Klaus “HF-Doktor” and from http://www.srcb.ro online and this appears the only point which is the same. Limits life of your radio, invalidates warranty’s and is generally not a Smart way. But this is the power modification Photo: http://www.neuner.de (c)
Anytone AT-5555N & CRT Superstar 7900
Solder closed OP1
CRT 7900 Software:http://www.filedropper.com/ss7900setup10011 (limited time only, when expires its gone)
Albrecht AE-2990 AFS
AE2990AFS-Amateur-extension-to-Multi-Mode-Features
Stabo XM-4060e
Wire and Jumper
Team TS-6M LCD
Cut the wire and move the jumper. 26515-27855 AM/FM unlocked. Bands a, b, c
Danita 310m
Cut the wire and move the jumper. 25.1-30.1 AM/FM
Albrecht AE-4200 EU
Team MobileCom. Export Mode
Close OP1 and OP2 with solder, and for 0 ending and high power use the same modification as CRT One
CRT:
President:
Lincoln II (Only for initial pieces of first edition 1000 pieces to update to v2) Not for new models
Grant II Schematic:
Top Gun Quad 5 Export Mode and PCB Adjustments
Modification_Top_Gun_Quad-5_ENG
President Lincoln II Export Mode
Yaesu FT-991 MARS / CAP
Midland Base Camp 446
Grant II Premium: (HF-Doktor Information)
Buongiorno,gradirei sapere su quali trimmer devo agire per aumentare la modulazione e i watt in AM, nel mio Crt Superstar 6900, cordiali saluti Fabio
LikeLike
AMOD is AM modulation
APWR (H) is AM power high
APWR (L) is AM power low
FMPWR (H) is FM power high
FMPWR (L) is FM power low
SSBPWR (H) is SSB power high
SSBANL is SSB modulation
LikeLike
I see you don’t monetize simonthewizard.com, don’t waste your traffic, you
can earn additional cash every month with new monetization method.
This is the best adsense alternative for any type of website (they approve all websites), for more
details simply search in gooogle: murgrabia’s tools
LikeLike
Hi Simon
I asked the question about the Mars mod for the FTDX 101D. The mod on your blog is for the European Version. I’m in Australia, so is it the same. Also is it a straight solder for the jumper or is it like the YAESU FT 891 where you can just short the jumper whilst doing a reset on the radio. Most people say you have to solder the jumper on the ft891.
Hopefully the Yaesu FTDX 101D is the same.
Please let me know.
Thanks Simon
Kind Regards
Shane
LikeLike
Hi Shane.
From my understanding it’s close the point not a temporary bridge.. Australia version I’ve not the modification. Just EU at the moment.
Regards
🧙♀️
LikeLike
Hi Guys
Just wondering if anyone has come up with MARS mod extended transmit for the Yaesu FTDX 101d yet.
Kind Regards
Shane
LikeLike
Hi Shane
Yep it’s on my blog
Regards
🧙♀️
LikeLike
Hi Simon. For the CRT Millenium, my local shop sells a version that is comutable 4W – 15W
I managed to make it 4W – 8W. Is it possible to make 4 – 15W? How?
LikeLike
Hi Good Afternoon. Maybe they solder across the output transistor and that way loose AM. Standard export mode is 4-8 watts AM/FM
Only way I guess short the output transistor.
Regards 🧙♀️
LikeLike
CRT Xenon service menue : transceiver off / SQ+EMG hold / transceiver on then FM Mod
LikeLike
Turn till 87-89 on the display for 2.0 kHz deviation but anymore than that makes the radio dirty. Normally it sits around 81-83 before moving. It’s being featured here in a few weeks as time not allow it.
LikeLike
My crt xenon has a very quiet modulation on fm uk.
Is this normal for this cb?
The mic gain is up on 10 but am told i sound so quiet.
Can you help?
With thanks
David.
LikeLike
Hi David. It can be adjusted in factory mode to make it higher. But these radios are sold in legal limits so are quiet. Sadly I’m not allowed to say how to access the factory mode as many have tried and it’s caused other issues.
Regards
🧙♂️
LikeLike
Has anyone managed to open up the frequencies on an Alinco DR-438..?
Can’t find anything anywhere..
Thanks
J
LikeLike
It’s unlocked as far as I know via microphone and switch on and change its configuration but I’ve not got this mod as never looked or asked
LikeLike
Thanks for the quick reply..
So just ptt and switch on ?..
J
LikeLike
No. It’s like with CRT Micron (Look it up) they’ll be some key pattern to unlock a menu to unlock the radio? That’s according to a Russian site. I don’t know how to access this menu.
LikeLike
Ok thanks Simon..
I have a go and post my results should I get it to open up ..
J
LikeLike
Also found this:
MARS/CAP is covered by a small software file installed via data cable. This then resets the radio. This software is dealer found and can be installed with a payment. The DR-438 is based on AT-588 which is also unlocked via exe file.
LikeLike
Ok great .. I have the data cable .. Just need to get the file ..
Much appreciated.
J
LikeLike
Looking for 11 meter conversion for the new president richard. Do you have any info on this? Thanks in advance.
LikeLike
Modifications II Area
LikeLike
New rev 980 Midland. Need a ch. King board.
Mark is all I can locate for a contact name
Link?? My cqdx game is lacking in frequency. Lol. Any help in the right direction appreciated
Thanks
LikeLike
I didn’t know midland made the 980. Channel king contact via Marks YouTube page: https://youtu.be/aLpBsG1O-pY
LikeLike
Good day sir, would you have any info on a realistic TRC 450 mobile fir channel mod? Thank you
LikeLike
Hi David. I think original came with MB8714 but needs MB8719 to expand channels but I’m not sure 100%
LikeLike
Conversion for high power on Stryker sr-25mc
LikeLike
No hello, No please, No thank you so use search it’s on the blog. Just 1 solder blob unlocks low, mid and hi on FM and low and Hi AM
LikeLike
Continues wipe frecventy on Yaesu vr120 D ? No Gaps. Thanks.
LikeLike
Hi Simon
I am looking to purchase a President Grant premium 11 what advantage would I have by getting the export version (will I lose UK CB channels?..)
LikeLike
Hi Frank. Thanks for the message. In export the Premium comes with the UK channels so you’ll not loose them. You will get Band A-L and UK40 too
LikeLike
Excellent thanks for your swift reply Simon very appreciated
Regards
Frank
LikeLike
Hi Frank. As I say in export mode you’ll get the UK band as part of it, higher output power that’s why heatsink and frequencies from 25.6-30.1 guess best idea is buy the radio expanded so dealer has checked out the power etc and all is well. That’s the best idea of all
LikeLike
Hi Simon :
Nanfone cb 40 . 25to 30 mod 4watt to 12 watt mods . i bought them in Cambodia out of the box 7 bands 38usd i like 29. Meg AM HAM Russian model much more 25 -30 . Please direct me to this mod.is up down microphone posable thank you marty Hurney n2qgu cb is more fun
LikeLike